We research and compare products using published specifications, features and owner feedback. When you buy through our links, we may earn a commission. As an Amazon Associate I earn from qualifying purchases. Learn more›

Cricut Explore Air 2 Smart Cutting Machine: A Step-by-Step Guide for Beginners

Learn how to set up, calibrate and use the Cricut Explore Air 2 smart cutting machine, from first cut to clean vinyl and cardstock projects.

Updated November 2026

The Cricut Explore Air 2 smart cutting machine is a Bluetooth-enabled cutter that turns paper, vinyl, iron-on and thin cardstock into precise shapes for crafts. In this guide you will set up the machine, load your material, make a test cut and avoid the mistakes that waste mats and blades. Most beginners can complete their first working project in one sitting.

What You Need Before You Start

Gather your supplies before you power on the machine so you are not stopping midway through setup. The Explore Air 2 works with a cutting mat, a blade housing, a fine-point blade and a computer, tablet or phone running the Cricut Design Space app.

Shopping for one? See our guide: 3 Best Cricut Maker 3 Craft Cutting Machine Options for 2026.

  1. The Explore Air 2 machine, power cord and USB cable
  2. A StandardGrip or LightGrip cutting mat matched to your material
  3. A fine-point blade installed in the blade housing
  4. A free Cricut Design Space account
  5. Your material, such as 12 x 12 inch vinyl or 65 lb cardstock
  6. A scraper tool and weeding tools for removing excess material

Set Up the Machine and Install the Blade

Place the machine on a flat, stable surface with clear space at the front for the mat to feed in and out. Plug it in, turn it on and pair it with your device over Bluetooth or USB. Design Space will walk you through the connection steps the first time.

Install the fine-point blade

Open the clamp, remove the blade housing and insert the fine-point blade with the blade body seated fully in the housing. Snap the housing back into the carriage. Cricut sets its own blade depth through the dial, so keep the dial at the setting Design Space recommends for your material.

Load Material and Run a Test Cut

Stick your material to the mat with its edges aligned to the grid lines, then press it down with the scraper to remove air pockets. Load the mat so the top edge goes in first and the arrows on the mat line up with the machine’s guides.

Before cutting a full project, run a small test cut. A 1 inch square is enough. If the blade drags, tears the paper or fails to cut through the backing, adjust the material setting or the dial and try again. Using a test cut on a scrap piece saves material and time.

Cut, Unload and Weed Your Project

Once the test looks clean, send the full design to the machine. Let the cut finish completely before unloading, and use the unload button rather than pulling the mat out by hand. Then remove the excess material around your shapes with a weeding tool, working slowly around small details.

Material Typical mat Common issue
Vinyl StandardGrip Lifting at corners; press edges down before cutting
Cardstock LightGrip or StandardGrip Tearing; use a fresh blade and lower pressure
Iron-on StandardGrip Shiny side must face down on the mat

Common Mistakes to Avoid

  • Skipping the test cut, which often leads to wasted mats and shredded material.
  • Using a dull blade. Manufacturers specify replacement intervals, and a dull blade causes tearing and incomplete cuts.
  • Pulling the mat out mid-cut instead of unloading it properly.
  • Forgetting to remove the protective film from the mat before first use.
  • Cutting material wider than the mat grid, which can jam the carriage.

A fresh set of cutting mats in different grip strengths lets you match the adhesion to paper, vinyl or iron-on. View on Amazon

A weeding tool kit makes removing small pieces from vinyl far easier than using fingers alone. View on Amazon

Replacement fine-point blades keep cuts clean, especially on cardstock and vinyl. View on Amazon

FAQ

Does the Cricut Explore Air 2 cut wood or thick materials?

The Explore Air 2 is designed for paper, vinyl, iron-on and thin materials. Manufacturers list specific thickness limits, so check the official specifications before cutting anything heavier.

Why does my design cut only partway through the material?

This usually means the blade depth or material setting does not match your material. Run a test cut and adjust the dial or setting in Design Space.

Can I use the machine without a computer?

You can connect through Design Space on a phone or tablet, so a full computer is not required. Check the official Cricut site for the latest device compatibility.

Conclusion

With the machine set up, the blade installed and a test cut completed, the Explore Air 2 becomes a reliable tool for everyday crafts. Keep your blades fresh and your mats clean, and most cutting problems are easy to fix. Refer to the official Cricut manual for model-specific settings and safety guidance.

Colin Foster

About Colin Foster

Colin Foster is part of our editorial team and reviews and edits our arts & crafts supplies guides, checking product details against manufacturer specifications and owner feedback.

About the author

Colin Foster
Colin Foster

Colin Foster writes reviews and buying guides for Crafts Center.